1800-B: Difference between revisions
No edit summary |
No edit summary |
||
| Line 19: | Line 19: | ||
The Type 1800-B is a high impedance, high frequency voltmeter, an updated version of the [[1800-A|1899-A Vacuum-Tube Voltmeter]] with improved power supply, including a two-stage voltage regulator, and updated with the new GR-874 probe adapter. | The Type 1800-B is a high impedance, high frequency voltmeter, an updated version of the [[1800-A|1899-A Vacuum-Tube Voltmeter]] with improved power supply, including a two-stage voltage regulator, and updated with the new GR-874 probe adapter. | ||
Two range extension accessories were available, the Types [[1800-P2|1800-P2 High-Frequency Multiplier]], and the [[1800-P3|1800-P3 Low-Frequency Multiplier]]. | |||
On the AC voltage ranges, except for the two lowest, the 1800-B is essentially a peak-reading instrument, but the scales are calibrated to give readings of RMS values of sinusoidal voltages. The upper frequency limit approaches 500 MHz with corrections, approximately 100 MHz without. For DC measurements, binding posts are provided along with a shorting strip for the open grid mode. For AC measurements, a hard-wired UHF probe is provided, stored in the top compartment along with its accessories. When in the storage position, the probe plugs into the front panel binding posts where low-frequency AC measurements are made. When UHF measurements are desired, the probe is removed for direct connection, the nose piece can be removed to reduce probe capacitance. Also located in the top compartment is a 50 Ω disk resistor used to convert the probe impedance, along with adapters for [[274|GR Type 274]] and [[GR-874|Type 874]] coaxial connectors. | |||
The 1800-B utilizes two RCA type 9005 "Acorn" UHF diodes (see data sheet below). | |||
==Specifications== | ==Specifications== | ||
Revision as of 16:38, 17 May 2024
The General Radio 1800-B Vacuum-Tube Voltmeter was introduced in Catalog O (1956) and remained available through Catalog Q (1961).
The Type 1800-B is a high impedance, high frequency voltmeter, an updated version of the 1899-A Vacuum-Tube Voltmeter with improved power supply, including a two-stage voltage regulator, and updated with the new GR-874 probe adapter.
Two range extension accessories were available, the Types 1800-P2 High-Frequency Multiplier, and the 1800-P3 Low-Frequency Multiplier.
On the AC voltage ranges, except for the two lowest, the 1800-B is essentially a peak-reading instrument, but the scales are calibrated to give readings of RMS values of sinusoidal voltages. The upper frequency limit approaches 500 MHz with corrections, approximately 100 MHz without. For DC measurements, binding posts are provided along with a shorting strip for the open grid mode. For AC measurements, a hard-wired UHF probe is provided, stored in the top compartment along with its accessories. When in the storage position, the probe plugs into the front panel binding posts where low-frequency AC measurements are made. When UHF measurements are desired, the probe is removed for direct connection, the nose piece can be removed to reduce probe capacitance. Also located in the top compartment is a 50 Ω disk resistor used to convert the probe impedance, along with adapters for GR Type 274 and Type 874 coaxial connectors.
The 1800-B utilizes two RCA type 9005 "Acorn" UHF diodes (see data sheet below).
Specifications
- Voltage Range: 0.1 to 150 V AC in 6 ranges; .01 to 150 V DC in 6 ranges
- Accuracy: DC and AC ±2% of full scale on 6 ranges; AC accuracy is for sinusoidal voltages
- Input Impedance: at low frequencies AC input resistance 25 MΩ; higher frequencies see manual; DC input resistance is 10 MΩ or open grid, selectable
Links
- Experimenter September 1956 describing Type 1800-B
- Experimenter May 1948 describing Type 1800-P2
- General Radio 1800-P3 Low-Frequency Multiplier Data Sheet 700-C 1954
- Experimenter December 1948 describing Type 1800-P3
- RCA 991 Voltage Regulator Data Sheet 1939
- RCA 9005 UHF Diode Data Sheet 1942
